Home > Not Working > DVD-rom May Work Only After Restart

DVD-rom May Work Only After Restart

Contents

good luck all and if all else fails -- contact the maker of your computer and see if it is under warranty -- they will replace it for free is what How do you determine the 'most potent effect' for overlapping spells? Only Bios setting i've changed is the onboard sound to enabled for the video card. Karen Report charbel- Apr 4, 2010 at 10:12 AM did you try To roll back to a previous driver: Open Device Manager. http://computermacintosh.com/not-working/usb-dont-work.html

Step 7: Testing for CD/DVD drive failure If you suspect that the drive may be bad after using the previous steps, test the drive to see if the hardware has failed. Your Regedit-tip did the trick in the end, but I think uninstalling SecuROM helped. –Marcus L Feb 8 '10 at 20:48 You should add to "Other things to try": Thank you! Thanks again :-) Report 123- Apr 24, 2010 at 03:15 AM there is no upp er or lower filter Helpful +13 Report fuck May 22, 2010 at 08:47 PM you try

Dvd Drive Not Working Windows 10

Helpful +34 Report mindex Sep 18, 2009 at 06:35 AM Clear SOLUTION!!!!!!!!!!!!!!!!!!!!! CD or DVD is not bootable Not all CDs and DVDs are bootable. Press Escape and it will ask you how you wish to quit, choose save and exit. The drive name should be removed from the list (and the DVD/CD-ROM drives category will also be removed if there is only one drive).

They all worked. I have a really big problem however that I'd really appreciate some help with (and please bare with me, I'm a novice at all this!) General Discussion Boot, automatic restart don't Please tell me the solution for the above problem. 4 8/5/2007 (5:12 am) by awesomeo awesomeo (2229 Posts) Check your device manager to see if the drives show up at Cd Drive Not Reading Disc The following procedure is an example of how to correct a No burner is currently available message in CyberLink Power2Go.

I had a network card, the type you install into an expansion slot in the back of the computer, which I installed. Hopefully it will help you. Not setup properly in CMOS setup (BIOS) If the CMOS is not properly set up, the computer may ignore or not look at the CD-ROM or DVD as a bootable option. Step 5: Testing for CD/DVD drive failure If you suspect that the drive may be bad after using the previous steps, test the drive to see if the hardware has failed.

Turn on the computer and immediately press the F10 key repeatedly until the BIOS Setup Utility screen appears. Cd Rom Not Working And in that case, Sony will once again have proven they should not attempt to be a software company. Use the arrow keys to navigate to the Storage tab. Again, I just have to leave the disc in and reboot.

  • Five USB connected optical drives for CD Audio production using Nero 11 Toshiba Touch Screen Laptop with Win 10 64 bit HP fireberd View Public Profile Find More Posts by fireberd
  • Software for burning discs does not recognize the drive If the CD/DVD writing software displays notification that no drive is detected, use the steps in this section.
  • How do I not back down against an unstoppable force?
  • Step 4: Restoring system files Use Microsoft System Restore to return the system back to a time when the CD/DVD writing software was known to work.
  • Problem: "me too" with a twist.
  • Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build.

Cd Drive Not Working Windows 7

I selected from the bottom believing it was the most recent, it was called "CD-ROM Drive [IMAPI settings 1,5]." Click next and finish the instructions it gives you. http://www.computerhope.com/issues/ch000227.htm After I clicked on TSSTcorp CDRW/DVD TSL462C, under the device status, it says that : "This device is working properly. Dvd Drive Not Working Windows 10 I now have the "FIX IT" icon on my desktop and will use it!! Cd Drive Not Working Windows 8 If your computer has multiple disc drives, consider disconnecting one of the drives and use the other drive to try to boot from the disc.

Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading... check my blog Have you updated your firmware? If the CD-ROM does work from MS-DOS, this indicates that you have a corruption issue with Windows. After the CD/DVD software is reinstalled and the computer has been restarted, it should recognize the CD/DVD drive. Cd Rom Not Opening

This rule also applies to portable computers with removable disc drives. Follow the instructions on the download pages to download each applicable update. Figure : Configure a device If you are prompted for an Administrator password or confirmation, type the password or provide confirmation. http://computermacintosh.com/not-working/keyboard-certain-keys-don-t-work.html I did what he said, and my report is going to get done on time.

TechSpot Account Sign up for free, it takes 30 seconds. Cd Command Not Working Generated Fri, 13 Jan 2017 22:48:42 GMT by s_hp81 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.4/ Connection if it does show there but still dosen't show in windows check to make sure there isn't a conflict of jumper settings on all items hooked on that chain..

If the drive is still missing after using the troubleshooter, continue to the next step.

For more information about testing for CD/DVD drive hardware failures, refer to one of the following HP support documents: Desktop PCs: Testing for Hardware Failures (Windows 10, 8) (in English) Notebook Complementary Content Has my ISP mangled my DNS reverse lookup record for a single static IP address? Dvd Player Not Reading Disc On a desktop computer Press and hold the power button for 5 seconds to turn your computer completely off.

tis gonna run me around 100.00. I even checked to make sure all drivers were working properly. Thanks Sep 26, 2006 #5 tyleronline TS Rookie Topic Starter Posts: 66 O.k I have reinstalled the firmware as I did have the latest version and that seems to have have a peek at these guys I'm confused??

Sep 25, 2006 #3 smore9648 TS Rookie Posts: 697 Are the jumpers setup correctly to slave? To reset the BIOS, use one of the following sets of steps, depending on the type of computer you are using: To reset the BIOS on a notebook computer, press F9 Reboot and test. yay.

Figure : Example of CD/DVD drive listing in notebook BIOS Press Esc, then press Enter to Exit BIOS.